How to Regrip a Golf Putter: A Step-by-Step Guide for Better Feel
Learn how to regrip a golf putter at home with tape, solvent and a few simple steps. Get a fresh, tacky grip that improves feel and control on the greens.
Updated November 2026
Learning how to regrip a golf putter is a straightforward job you can finish in under an hour with basic tools. You will remove the old grip, clean the shaft, slide on a new grip with solvent, and let it cure so it sits firm and even in your hands. A fresh grip improves feel and helps you hold the putter the same way on every stroke.
What You Need Before You Start
Gather your supplies first so you are not stopping halfway through with tacky solvent on your hands. Most putter regrips take less than 45 minutes once everything is laid out.
Shopping for one? See our guide: 7 Best Cobra Golf Blade Putter Picks for Every Stroke (2026).
- A replacement grip sized for putters (standard or oversize)
- Grip solvent or a mix of isopropyl alcohol and a few drops of dish soap
- Double-sided grip tape (if your grip does not come with it installed)
- A utility knife or razor blade
- A vise or a clamp to hold the shaft steady
- Rags, a small spray bottle and a clean work surface
Step 1: Remove the Old Grip
Start by cutting a slit along the length of the old grip from the top to the bottom, then peel it away from the shaft. If the grip is stuck, place the shaft in a vise and twist the grip gently while pulling. Heat from a hair dryer on low can soften old rubber and make removal easier.
Once the grip is off, scrape away any old tape residue with the blade. Wipe the shaft clean with a rag dampened with alcohol so no dirt or oil remains.
Step 2: Prepare the Shaft and Grip
Check the shaft end for a plug or sharp edges and make sure the surface is smooth. If you are using a grip that needs tape, apply one strip of double-sided tape along the shaft, leaving a small gap at the top so the grip seats fully. Many modern putter grips are sold without tape, so follow the packaging instructions for your specific model.
Spray the inside of the new grip and the shaft with solvent. Work quickly, because the solvent starts to evaporate within a minute or two.
Step 3: Install the New Grip and Let It Cure
Slide the grip onto the shaft with a firm, steady push and a slight twist to spread the solvent evenly. Align the grip so the logo or alignment line sits where you want it, since you cannot reposition it easily once the solvent sets.
Wipe off any excess solvent with a dry rag, then stand the putter upright with the grip end facing up. Let it cure for at least 4 to 6 hours at room temperature. Manufacturers often recommend leaving it overnight for the strongest bond. Avoid gripping the putter during this time.
Checking the Fit
Once cured, set the putter in your normal address position and confirm the grip sits square to the putter face. Lightly twist the grip to make sure it does not spin on the shaft.
Common Mistakes to Avoid
- Skipping the cleaning step, which leaves oil that weakens the bond
- Using too much solvent, which can cause the grip to slide or feel loose
- Installing the grip at the wrong angle because you rushed the alignment
- Testing the putter before the grip has fully cured
- Choosing a grip size by guess instead of measuring your hand, since grip thickness changes how your wrists and forearms work
Recommended Gear
A putter-specific grip kit makes the process easier because the tape and solvent are often matched to the grip. Search for putter grip kits with solvent included.
A small clamp or bench vise keeps the shaft steady while you pull off the old grip. View on Amazon
Replacement grips in a range of sizes help you match your current feel or test a thicker option. View on Amazon
FAQ
How long does a putter grip last?
Many golfers replace putter grips every one to two years, depending on how often they play and how much moisture and sweat the grip collects. Replace it sooner if the surface feels hard, slick or cracked.
Can I regrip a putter without solvent?
You can use double-sided tape alone on some grips, but solvent helps the grip slide on smoothly and bond evenly. Without it, the grip is harder to align and more likely to shift over time.
Do I need to remove the old grip completely?
Yes, you should remove the old grip and clean the shaft before installing a new one. Leftover rubber or tape residue prevents the new grip from seating properly.
Conclusion
Regripping a putter comes down to clean removal, careful preparation and a full cure before you play. Take your time with alignment and follow the manufacturer’s curing time. A fresh grip can noticeably improve your feel and consistency on the greens.
Related reading
- Scottie Scheffler Putter Grip Golf Pride: What He Uses and How to Get It
- Putter Butter Golf Club Protector: How to Choose and Use One (2026)
- Peter Putter Golf Club: What It Is, How to Use It, and Who It Suits
Ready to choose one?
